1～15 item / All 17 items
Non-destructive testing device that simply strikes a concrete surface with a hammer for a measurement time of 2 seconds.
This is a concrete moisture meter using the capacitance measurement method. It comes with an automatic sieve wet screener, a weighing balance, and a printer, providing everything needed for measurement. It can also measure the moisture content of fine aggregates (sand).
All necessary items for measurement, including an automatic sieve wet screener, weighing scale, printer, etc., are included.
This is a concrete moisture meter using the capacitance measurement method.
You can select a measurement mode that can accommodate any type of sample or condition.
This is a moisture meter that can switch between high precision of 0.01% and standard 0.1%, capable of displaying moisture content through infrared heating and drying.
This is a moisture meter using infrared heating and drying.
The FD-720 can switch between high precision of 0.01% and the standard 0.1% to display moisture content. To achieve high-precision measurements, this device employs a balance unit with a resolution of 1mg called "Uniblock," and it is equipped with a newly developed medium-wave infrared quartz heater with a large heat capacity of 625W in the drying section. Additionally, it features a "Rapid Drying Mode" enabled by drying control software, allowing moisture values to be obtained in a short measurement time, significantly reducing measurement time for certain samples. The memory area can store 10 different measurement conditions, eliminating the need for manual setting adjustments for samples with different measurement conditions. This device is positioned as a moisture meter for quality control and inspection departments that require advanced moisture management, and it can be used for high-precision moisture control.
By drilling two holes at the desired measurement location and simply inserting the sensor, it is possible to measure moisture.
The HI-800 is a compact and lightweight concrete mortar moisture meter. For the repair of exterior walls, epoxy resin is injected into damaged concrete (mortar), and measuring the moisture content with this device at that time will help determine the optimal injection timing. By drilling two holes at the desired measurement locations and simply inserting the sensors, moisture measurement is possible. This device is a moisture meter developed based on the "Public-Private Joint Research on Repair and Renovation Techniques for Exterior Materials" by the Ministry of Construction's Building Research Institute. For more details, please contact us.
Simply insert the sensor into the soil to easily measure the volumetric water content of the soil in just a few seconds!
The DIK-311E is a soil moisture meter that allows for easy measurement of soil volumetric water content in just a few seconds by simply inserting the theta probe (sensor) into the soil. The sensor measures by detecting changes in dielectric constant and is waterproof, allowing it to be directly buried in the ground. It can measure volumetric water content from 0 to 100% with an accuracy of 5%, and with calibration, it can achieve an accuracy of 2%. For more details, please contact us.
The oil moisture meter enables highly reliable measurement of moisture in oil.
The MM70 is suitable for preventive maintenance of systems that use oil. By measuring the moisture activity value, it quantifies the risk of free water generation and prevents lubrication system troubles in advance. The probe can be directly inserted into the process pipe via a ball valve, eliminating the need to drain oil from the operating system. For more details, please contact us.
Essential for the installation of the waterproofing layer. Measurement of moisture on the surface of the concrete slab.
In the construction of the waterproof layer for the deck slab (concrete slab) of road bridges, if the surface moisture content after concrete surface treatment is not appropriate, blisters or peeling may occur in the waterproof layer, resulting in the expected performance not being achieved. The HI-100 adopts an electrical resistance method that minimizes the influence of surface irregularities, and it is equipped with a conductive rubber sensor, allowing the sensor to closely adhere to uneven surfaces, thereby improving accuracy. 【Features】 - Accurate measurements can be made regardless of the finishing condition of the concrete slab surface. - Ideal for sites such as new construction or asphalt replacement work. For more details, please contact us.
Rapidly confirm moisture content on-site with a compact and lightweight rock and soil investigation testing device!
"WARP" is a surface-type RI moisture meter designed for the information-based construction of embankments, which is necessary for the task of "confirming that the moisture content of the embankment material falls within the range that achieves the specified compaction degree." It allows for easy, quick, and accurate measurement. Compared to conventional RI density moisture meters, it is compact, lightweight, and easy to handle. It enables rapid confirmation of moisture content on-site, and repeated measurements can be performed with ease. Additionally, the measurement data is stored in the internal memory of the device and can be viewed through key operations on the device. The data in the internal memory can be transferred to a USB memory stick via the USB port on the side of the device. 【Features】 - Compact and lightweight for easy handling - Rapid confirmation of moisture content on-site - Compatible with soil materials with moisture content up to approximately 40% - Significantly simplifies the measurement process - Reduces the effort required for drilling operations by setting the source depth to 6 cm *For more details, please feel free to contact us.
This is a concrete moisture meter using capacitance measurement method. NETIS registered product: TH-000001-VE
***Summary*** Concrete strength is generally measured by the compressive strength 28 days after pouring. However, even if it is deemed insufficient at that point, rework is practically impossible. Against this backdrop, there is a demand for measurement equipment that can quickly determine the water-cement ratio of fresh concrete (mortar) on-site. Typically, the amount of cement in the water-cement ratio can be accurately understood from weighing records, but the water content must also consider the surface water adhered to aggregates and adjustments for slump compliance, making it extremely difficult to accurately grasp the unit water amount. If moisture measurement of fresh concrete (mortar) is conducted at the time of construction and the unit water amount is determined, allowing for an accurate assessment of the water-cement ratio, such troubles can be avoided.
Measurement of artificial lightweight aggregate concrete and gypsum board is also possible.
This is a handheld moisture meter that uses a high-frequency capacitive method, allowing measurements to be taken simply by setting the dial in advance and lightly pressing it against the measurement area.
Measurable from the surface to the interior.
It is a small and lightweight wood moisture meter that can measure simply by lightly pressing against the surface of the wood without damaging it.
This is a wood moisture meter that adopts the electrical resistance method, which has been widely used traditionally.
The MT-700 is a wood moisture meter that widely utilizes the electrical resistance method. It can adjust the displayed moisture value between -9.9% and +9.9% to match management conditions, making it suitable for actual circumstances. It stores data for 16 types of wood species. By calling up the sample number, measurements can be taken directly without conversion. For more details, please contact us.
Measure and manage the unit water content that greatly affects the durability of concrete structures!
The Continuous RI Concrete Moisture Meter COARA (Soil and Rock Engineering) can measure and manage the unit water content, which greatly affects the durability of concrete structures, against the total amount of concrete actually used. This ensures the quality of concrete structures, particularly their durability. The measurement principle involves detecting the transmission of neutron rays related to moisture content and the transmission of gamma rays related to density, calculating moisture content and density based on calibration formulas, and ultimately determining the unit water content of the concrete using other physical property values. Since the density of concrete changes with moisture content and pumping pressure, it is necessary to measure density simultaneously. For more details, please contact us or refer to the catalog.
A tatami moisture meter that allows for moisture measurement of tatami mats, rice straw floors, etc., without complicated adjustments.
The "HX-300" is a tatami moisture meter that displays moisture levels simply by inserting needle-like sensors into the tatami surface or tatami base. It has built-in calibration curves for tatami surfaces, rice straw bases, and tatami boards, allowing for measurement and direct reading of moisture values without complicated adjustments. Additionally, it is equipped with a temperature sensor, which automatically performs temperature compensation for the tatami. 【Features】 ■ Built-in three types of calibration curves ■ Temperature compensation function ■ Auto power-off feature ■ Alarm setting function ■ Moisture value correction available *For more details, please feel free to contact us.
